Stripped faucet handles are often the result of wear and tear. These issues can be caused by cracked handles, worn splines, or even worn valve stems and cartridges. Fortunately, a simple repair can resolve these problems. Here are some basic steps you can take.

Repairing a faulty shower faucet handle

First, locate the water valves for the shower faucet. If there are any, turn them clockwise. If the stem is damaged, it is easier to repair by soaking it in a bucket of vinegar, or you can use a wrench to pry it off. You can also use vinegar to dissolve any mineral buildup in the handle. The valve stems are held together by retainer nuts and clips.

To remove the handle, use a hex wrench or a screwdriver to loosen the nut holding it to the handle. Once you have loosened the nut, you should be able to remove the cartridge. You may also need a small screwdriver to remove the cartridge retaining clip.

If you can’t turn the shower handle, you can use plumbing tape to wrap the stem of the shower valve. If the plumbing tape is not enough to keep the handle in place, you may need to replace the shower valve cartridge. Changing the cartridge will prevent further plumbing problems. It is also possible to fix a stripped shower handle by cleaning it or replacing it.

Before you begin replacing the cartridge, turn off the water. If you don’t have a dedicated bathroom valve, shut off the main water supply to the shower first. Then, turn the water back on. If the cartridge is not leaking, it is likely a worn-out washer or rubber seal. Keeping the faucet closed during this process will prevent the parts from spilling out onto the floor.

Before you try to fix the handle, you should first try replacing the shower valve. This fix is a simple solution to most shower faucet problems, but you may need to do it yourself. If the repair does not work, you may have to call a plumber. Once you have the replacement valve, you can reassemble the shower valve and install it on the trim plate.

Next, you should clean the stem. It may have mineral deposits in it. You can use vinegar to clean it. You can also replace the faucet cartridge by replacing the parts, which is much easier and cost-effective. When replacing the stem, you should remember to follow all directions to ensure a good seal.

Repairing a faulty kitchen faucet handle

To repair a faulty kitchen faucet handle, you must first identify the faulty part. The faucet handle is usually held to the main body by a tiny screw. Sometimes this screw is covered by a decorative cap or plastic disc. To get access to this screw, use a pocket knife to pry off the cap. You can then loosen the nut by rotating it with a wrench or slip-joint pliers.

The most common problem with faucet handles is worn on the stem. This is also called the cartridge. This part attaches to the handle and controls water flow. If the stem is stripped, the handle becomes loose and sometimes spins on its end. You may need to replace the handle.

Depending on the type of faucet, you may need to replace the whole faucet or just fix the handle. For ball faucets, you may need to purchase a repair kit. The repair kit includes the parts needed to fix the faucet stem and stop the leak. Alternatively, you may be able to salvage the cap and handle.

Before you can fix the handle, you must remove the stem. To do this, you will need an Allen wrench or flathead screwdriver. Next, you need to unscrew the set screw. You can also unscrew the plug that is underneath the handle. You should then be able to pull out the handle.

Once you have the new stem, you must insert it into the faucet housing. Make sure the tabs on the new stem match the slots on the housing. Then, you must replace the decorative cap and screw it into the stem. The handle should now be secure. If you cannot repair the faucet handle yourself, you can contact an expert to repair it.

Fortunately, repairing a faulty kitchen faucet handle is easier than you may think. In some cases, the problem may be a worn-down screw, which you can simply replace with a new one. Alternatively, a damaged mechanism may require a replacement handle.

 

Call Now Button